Корзинки для игрушек
19-04-2011 10:27
к комментариям - к полной версии
- понравилось!
Это цитата сообщения Рождена_Весной Оригинальное сообщение
Корзинки для игрушек
[показать]
[600x300]
Take one of your 18 ½ x 28 inch pieces and fold it in half with right side in, short ends together. Now sew up the sides, leaving the top open. Repeat on the five left.
[600x300]
You will need two sheets for one basket, and they should look like this. I alternated them so that I had a different pattern on the inside then I did on the outside.
[600x300]
Leaving them wrong side out, take and fold your corners down like shown. To make sure that you are aligned correctly, just make a crease on the bottom fold and line that up with the seam on the inside, make sure your seam is flattened all the way out.
Take a ruler and mark a line 7½ inches long as shown and pin. After you make the line measure from the point to the line and you should get 3¾. Repeat on the other side, and do this on all of your pieces.
[600x300]
It does help if you have a cutting mat with measurements, you can see how I lined up the corners to make sure they were symmetrical. If you don't, that's fine, just eyeball it.
[600x300]
Now sew along the lines on each of your corners.
[600x300]
Take the pieces you want on the outside and turn them right side out, folding the corners down. Drop the Plexiglas into the bottom.
[600x300]
Leaving your other pieces right side in, fold your corners under and place inside of the other shell, on top of the glass.
[600x300]
Next fold your outer shell over about a half inch and pin then repeat on the inner shell...
[600x300]
using the same pins so that you are pinning them together. Make sure the two overlap some where you will stitch together.
[600x300]
Take your three smaller pieces and fold the ends over a ¼ inch and sew both ends.
[600x300]
Fold in half and insert on what you would like to be the backside of the basket. Pin in place, making sure that whatever rod you use will fit through. I tested mine now to make sure.
[600x300]
To make sure that I had it centered, I just pulled the basket straight at the seams and eyeballed it.
[600x300]
Now with a little longer stitch length just sew all around the top, making sure to get all the layers included in the stitch.
[показать]
[показать]
[показать]
[показать]
вверх^
к полной версии
понравилось!
в evernote
Это цитата сообщения Рождена_Весной Оригинальное сообщение
Корзинки для игрушек
[показать] [600x300]Take one of your 18 ½ x 28 inch pieces and fold it in half with right side in, short ends together. Now sew up the sides, leaving the top open. Repeat on the five left.
[600x300]You will need two sheets for one basket, and they should look like this. I alternated them so that I had a different pattern on the inside then I did on the outside.
[600x300]Leaving them wrong side out, take and fold your corners down like shown. To make sure that you are aligned correctly, just make a crease on the bottom fold and line that up with the seam on the inside, make sure your seam is flattened all the way out.
Take a ruler and mark a line 7½ inches long as shown and pin. After you make the line measure from the point to the line and you should get 3¾. Repeat on the other side, and do this on all of your pieces.
[600x300]It does help if you have a cutting mat with measurements, you can see how I lined up the corners to make sure they were symmetrical. If you don't, that's fine, just eyeball it.
[600x300]Now sew along the lines on each of your corners.
[600x300]Take the pieces you want on the outside and turn them right side out, folding the corners down. Drop the Plexiglas into the bottom.
[600x300]Leaving your other pieces right side in, fold your corners under and place inside of the other shell, on top of the glass.
[600x300]Next fold your outer shell over about a half inch and pin then repeat on the inner shell...
[600x300]using the same pins so that you are pinning them together. Make sure the two overlap some where you will stitch together.
[600x300]Take your three smaller pieces and fold the ends over a ¼ inch and sew both ends.
[600x300]Fold in half and insert on what you would like to be the backside of the basket. Pin in place, making sure that whatever rod you use will fit through. I tested mine now to make sure.
[600x300]To make sure that I had it centered, I just pulled the basket straight at the seams and eyeballed it.
[600x300]Now with a little longer stitch length just sew all around the top, making sure to get all the layers included in the stitch.
[показать] [показать] [показать] [показать]Вы сейчас не можете прокомментировать это сообщение.
Дневник Корзинки для игрушек | svetik_ivanova-85 - Дневник svetik_ivanova-85 |
Лента друзей svetik_ivanova-85
/ Полная версия
Добавить в друзья
Страницы:
раньше»