[300x347]

Компания Peavey объявила о выходе новой версии “виртуального” гитарного усилителя ReValver™ MK III, на этот раз действительно моделирующего работу электронных ламп в различных режимах. Пакет позволяет музыканту получить собственный звук, выбирая из безграничного количества комбинаций преампов, усилителей мощности, эффектов.

В отличие от подобных программ, таких как Guitar Rig и Amplitube - Revalver предоставляет полный доступ к управлению параметрами моделирования, например, каждая лампа в усилителе может быть замененеа на лампы 17 других типов, возможен даже выбор типа выпрямителей питания и выходных трансформаторов! Программа так же включает 65 эффектов - педалек и rack-модулей.
Основанный на 40-летнем опыте создания реальных аппаратов, Revalver MKIII - наиболее гибкий и мощный продукт на сегодняшний день. Peavey ReValver MK III с высокой точностью моделирует 15 типов реальных гитарных усилителей, таких как Peavey 6505®, JSX®, Classic®, ValveKing®, Triple XXX® с учетом реальной схемотехники и взаимодействия всех компонентов и включает виртуальный педалборд с эффетами, такими как chorus, distortion, wah, tremolo, compression, limiter, delay, octaver и др.

Краткий список компонентов и возможностей: 15 моделей усилителей таких как Peavey 6505®, JSX®, Classic®, ValveKing® и Triple XXX®, 12 преампов, 9 усилителей мощности, 19 компактных педалек, 11 эффектов, более 150 моделей динамиков и кабинетов, 7 утилит (тюнеры, анализаторы сигнала), программируемое управление по MIDI, совместимость с VST, AU, ASIO/WDM, CoreAudio. Минимальные требования к компьютеру: 1 GHz CPU, 512 MB RAM, 1024×768 дисплей, VST host или ASIO/WDM звуковая карта. Щелкнув правой кнопкой мыши на любом из компонентов, пользователь получает полный доступ к его схеме и настройкам через Tweak Module GUI Все лампы, трансформаторы и другие компоненты могут быть заменены на изделия других типов (более 17 вариантов) из входящей в программу библиотеки. Возможно даже менять режим работы каждого усилительного каскада.
Extensive Guitar Amp, Preamp, and Power Amp Modeling

Peavey ReValver Mk III models 15 of the world's most popular guitar amplifiers, including models of Peavey 6505®, JSX®, Classic®, ValveKing®, and Triple XXX® amps, through an exclusive algorithm that analyzes the interactions of the components on the circuit level based on the amps' original schematics. By controlling these amplifier models from the component level, ReValver is able to model every nuance with amazing accuracy.

ReValver also boasts 12 preamplifier models, 9 power amplifier models, 150 speaker simulations, and 20 microphone configurations, allowing the user to mix and match components to create a truly personalized custom tone.

Amplifier Models

[показать]	Peavey 6505® For over 15 years, the 6505® has been the super-high gain amp for hardcore rock players worldwide. Featuring 5 12AX7 preamp tubes, 4 6L6GC power amp tubes, and Patented Resonance and Presence controls, the 6505® is the sound of rock and metal.
[показать]	Peavey 6505+® The big brother of the 6505® boasts 6 12AX7 preamp tubes for additional bite.
[показать]	Peavey JSX® With unprecedented versatility, the JSX® offers the widest range of EQ options and gain structures. This 3 channel amp delivers sounds ranging from the Classic® 50 to vintage British to the modern Triple XXX® and all tones in between.
[показать]	Peavey XXX® Three all-tube channels of unrelenting sustain, gain, and power makes the XXX® the ULTIMATE tone machine. As hot as the name implies, the XXX(R) rips.
[показать]	Peavey ValveKing® Boutique features such as the patented Texture™ control take this amp from Class A/B saturation to vintage Class A tones, allowing  guitarists to coax virtually any tone from this amplifier
[показать]	Peavey Classic® Revered by guitarists of all genres worldwide for two decades, this amp delivers tone that is as classic as it’s name.
[показать]	ACM 900 Modeled after a British amp built with both valve and solid state components. It has only 1 channel but the two gain knobs controls the gain at two stages in the preamp. This is the sound of classic rock.
[показать]	Higher Modeled after the “treadplate” rectified amp which contributed to the sound of modern heavy rock. This amp has 5 modes, Normal/Clean/Modern/Red/Vintage, each with different frequency characteristics and gain.
[показать]	Bluesmaker Loosely based on a 1962 British classic. This amp has 2 channels, a normal and a tremolo channel.
[показать]	Fox ACS-45 Based on a widely revered amplifier that defined the sound of the British Invasion, it’s distinct tone is still as sought after today as it was then.
[показать]	Basic 100 With one channel for guitar and one for bass, this  amp has a lot of bottom. As the real thing, it does not provide much distortion but it is usually played “cleanish”. The guitar and bass channels have different gain and tone stacks. The bass channel even has a “Deep” switch, shifting the frequency response of the Bass knob. On the guitar channel, the Bright switch gives you a brighter sound on lower gain.
[показать]	Matchbox The MatchBox is designed to provide clean to overdriven amplification with a minimum of clipping. It has as many as 4 gain stages with considerable attenuation between stages. It has a power amp in a push-pull configuration but no negative feedback (NFB). The sound is fitting for both guitar and for bass. This amp is using a very special tube configuration which gives you an extra bright sound.
[показать]	LePetite This amp contains preamp 3 chains in parallel which are fed into one power amp. The 3 channels can be mixed individually with the “blend” knobs.The three types are Clean/Diode/Triode. The second part of the amp consists of 1 triode tube and a push-pull pair of pentodes.
[показать]	HomeBrew SE-1 The HomeBrew SE-1 is a low watt single ended amp with two channels. For a low watt circuit it has as many as 3 triode stages for gain. The amp has 2 channels, Clean/Dist.
[показать]	HomeBrew PP-2 The HomeBrew PP-2 is a low watt push-pull amp with two channels and Britishtone stack.

Preamp Models

---

[показать]

Peavey 6505 preamp: Peavey proudly introduces its 6505® Series guitar amplifiers, named in celebration of Peavey�s first 40 years, 1965 to 2005. The 6505® preamp features 5 preamp tubes, with presence and resonance controls and three-band EQ for taming their notorious tone.

---

[показать]

Peavey Classic 30 preamp: The Classic 30 has a dual channel preamp allowing quick variations of the tone - from vintage blues, to modern hard-rock and grunge tones. The boost switch is particularly useful in obtaining the more traditional �cranked-amp� tones without the harshness generated by sending too much low end to the power amp.

---

[показать]

Peavey JSX preamp: This amp delivers sounds ranging from the Classic(R) 50 to vintage British to the modern Triple XXX(R) and all tones in between. The versatile and comprehensive control section supplies a master volume pot and independent volume knobs for each of the 3 channels (Ultra, Crunch and Clean). Tone shaping is accomplished through passive controls for Bass, Mid and Treble on the Clean channel, while the Ultra and Crunch channels utilize active low, mid and high controls.

---

[показать]

Peavey ValveKing preamp: The ValveKing delivers a tone ranging from bluesey clean to crunchy and classic rock. The amp has a built-in spring reverb and separate tonestacks for the two Clean and Lead channels. The amp�s preamp section uses 12AX7 tubes. The ValveKing also feature global resonance, presence and reverb controls.

---

[показать]

Pre HB: Simple pre amp for clean and slightly overdriven sounds. The pre amp goes easily into overdrive, but distorts gently and relatively cleanly.

---

[показать]

Pre amp Duo: This pre amp has 2 parallel channels; a triode tube path and a diode clipping path. The tube sound mixed with diode distortion makes an interesting and dynamic mix as the two components deliver two different overtone spectra.

---

[показать]

�62 BluesMaker pre amp: This pre amp has been directly taken out of the BluesMaker �62 amp. It contains both channels, the clean and tremolo, including the tremolo controls.

---

[показать]

Basic 100 bass pre amp: This is the bass channel pre amp in the Basic 100. The tone controls does not include a �mid� as the original does not have one. The deep switch lowers the frequency of the bass control.

---

[показать]

Basic 100 guitar channel pre amp: This is the guitar channel pre amp from the Basic 100. It is rather clean and is difficult to distort as it contains only 2 triodes, none of which usually saturates.

---

[показать]

ACM 900 pre amp: This is the pre amp section from the ACM 900. The two gain knobs control the gain in two places in the chain.

---

[показать]

Flathill �Modern� pre amp: This is the �Modern� channel pre amp from Flathill. Very high gain and bright.

---

[показать]

Flathill �Normal Red� pre amp: This is the �Normal Red� channel pre amp from Flathill. High gain. This pre amp has a presence control, something that usually sits in the power section. It gives a little extra control over the brightness.

---

Power Amp Models

[показать]

Peavey 6505 power amp: Peavey proudly introduces its 6505(R) Series guitar amplifiers, named in celebration of Peavey�s first 40 years, 1965 to 2005. 6505(R) Series power amps feature four 6L6GC power amp tubes, with the amps presence and resonance controls.

---

[показать]

Peavey Classic 30 power amp: The Classic 30�s power amp section is pure EL84 heaven. By decreasing the drive on the preamp and increasing the level of the power amp, you can achieve great EL84 saturation.

---

[показать]

Peavey ValveKing power amp: The ValveKing �s power amp section features the classic 4x6L6 lineup. The ValveKing, however, adds the patented Peavey Resonance control, as well as a presence control.

---

[показать]

M-998: Simple power amp, which does not have a standard Long Tail Pair (LTP) to drive the push pull end stage, but is using 2 triodes in series, for extra gain. This power amp also uses a couple of tonal character filters, which can be tweaked in the Tweak GUI.

---

[показать]

Standard power amp #2: This power amp has a standard push-pull end stage, but not driven by the usual Long Tail Pair (LTP). It does have a �clean� switch for less drive and slightly different tonal character.

---

[показать]

�62 BluesMaker power amp: This power amp is taken directly out of the �62 BluesMaker. It has a drive and presence control. It has a standard Negative Feedback Loop (NFB) to which the presence control is attached to. The NFB shapes the distortion character of the power stage.

---

[показать]

Basic power amp: This power amp is taken directly out of the Basic 100. As the original amp, the power section has only a master control. Even though the power stage has a Negative Feedback loop (NFB), it is not attached to a presence control. The NFB shapes the distortion character, and the amount can be set in the Tweak GUI.

---

[показать]

ACM 900 power section: This power amp is taken directly out of the ACM 900.

---

[показать]

Flathill power section: This power amp is taken directly out of Flathill.


Effects, Stomp-boxes, and Utility Functions

Peavey ReValver Mk III features a robust selection of 30 stomp-box and effects including various types of chorus, distortion, wah, tremolo, compression, limiter, delay, octaver, and much more. A new FFT-based convolution reverb allows for very complex and smooth reverbs, including sampled spring reverb.

ReValver also boasts 7 Utility functions including tuners, analyzer, splitters, and more.

 

Stomp-Boxes

---

[показать]

OverDriver: This stomp box is wired somewhat like a guitar amp, in that it is using 3 stages of distortion, but all being diodes. The �Turbo� acts like a �Master�, adding some extra gain before the last stage. This stomp box could possibly be used stand alone, driving a speaker by itself.

---

[показать]

Chorus CS-1: This is a versatile stereo chorus with adjustable speed and modulation depth, stereo width, feedback, delay and 3 individually adjustable filter bands on the wet signal. (The filters are available in the Tweak GUI.) A chorus can be used to fatten up the sound.

---

[показать]

ACS CS1 compressor: A compressor is used to even out the volume so that the lower levels do not completely disappear. It would make any distortion module distort for longer.

---

[показать]

Limiter LM-3: A limiter is specially tailored dynamics compressor. This particular limiter compresses the sound a factor 50:1 over the given threshold. It will stop sounds or transients over this threshold, limiting the output volume.

---

[показать]

The Slow Grow SG-1: An auto swell effect follows you tones and removes the transients. This makes the sound appear being played backwards.

---

[показать]

Octapus: Behind every great tone there is a another tone waiting to come out. With Octapus you can release this sub octave, taken from and added to your melody. The frequency triggering algorithm will only work properly on a single note at a time. You may want to be careful with chords or it will not sound as expected. The Octapus is a tight and accurate Octaver stomp box.

---

[показать]

Flanger FL-Duo: A flanger works much like a chorus, by mixing a varying delayed signal with the original to produce a series of phase cancellations. These �notches� make up sound of the flanger. The FL-Duo, is actually two flangers rolled into one. They share the same knobs, except for the mixing controls.

---

[показать]

Texas Treble Maker: The Texas Treble Maker is a so called �treble booster�. The purpose is to equalize the frequency spectrum of the guitar to make the distortion smoother. The overtones of roughly every kind of sound are progressively fainter the higher up the spectrum they are. This means that the distortion a sound generates in a distortion circuit mainly originates from the overtones of the lowest frequencies of the sound. This places the frequency range of the distortion components in a particular place of the spectrum. - A treble booster is designed to reshape the clean sound so that the distortion components originates in equal amount from each overtone. The result is a much smoother distortion, and of course a lot more distortion.

---

[показать]

The Sher�ff: The Sher�ff stomp pedal constitutes a rather rough but versatile distortion effect. Modeled loosely after a 1980�s era cousin it�s perfect for blues and rock, either by itself or together with a clean amp channel.

---

[показать]

Re-Lay 2 Delay: The Re-Lay 2 is a double delay with a lot of options. You can set the volume of each tap, plus 2 individual filters (in the tweak GUI) per tap.

---

[показать]

Re-Lay 4 Delay: The Re-Lay 4 is a quadruple delay with a lot of options. You can set the volume of each tap, plus 2 individual filters (in the tweak GUI) per tap.

---

[показать]

Greener: A classic, yet so simple. This late �70s solid state stomp box is using a diode clipping circuit, shaped by pre-, and post filtering for optimal smooth overdrive / distortion.

---

[показать]

Driver: This is a very versatile stomp box which delivers anything from smooth overdrive (with �Blues� turned up) to a heavily distorted and overloaded sound (�Gain� and �Muffler� turned up high). The module is using a modified amp tone stack which allows for heavy mid scooping. This box does a good job in both blues and Rock �n� Roll.

---

[показать]

MagnaVibe: A vibrato is (and don�t confuse this with a tremolo) frequency modulation, similar to when you move the string up and down, changing its pitch. This vibrato allows you to select a rate between 0 and 10 Hz, as well as a general depth. A knob for �delay� allows the vibrato to kick in a little bit after you pluck the string, making it more transparent when you play fast. Two modes are available, an �standard digital� one, and emulation of a certain �magnetic� stereo amp.

---

[показать]

Tremolo: A tremolo is (and don�t confuse this with a vibrato) amplitude modulation. This effect �rotates� the volume at the range of 0-10 Hz. Two variants are included, the classic �digital� tremolo (multiplying the signal with a sine) and the even more classic �tube bias� tremolo (adding a sine to the bias of a tube, partly saturating the signal). The tube bias variant adds a natural overtones clarity. The digital variant can adjust the up / down slope of the transition, going from soft to pulsing.

---

[показать]

Wow-Wah!: A Wah pedal is a low-, high-, or band pass filter with adjustable frequency. At the point of cut off, there is a peak with adjustable resonance, making the guitar sound �waaaoooowwwoooaaa�. The resonance has similarities with the human mouth, hence the name. The frequency can be controlled either by a midi pedal (or the main knob) or by automatic rotation. The resonance can range between any 2 frequencies of your choice. An extra knob for addition of overtones can give the guitar a clearer tone.

---

[показать]

BassBox: This is a distortion pedal with a slightly different harmonic spectrum. The even harmonics are stronger than the odd, making the distortion very smooth, bordeline �clean�. A second gain knob allow ordinary diode clipping, being somewhat asymmetrical. This module can be used for adding just a little bit of color and spice to the sound. Great for bass due to the harmonic spectrum.

---

[показать]

ShutUp Sch-1b, Noise Gate: A noise gate is a simple way to get rid of noise in the signal. The traditional way such an effect works is lowering the volume of the signal when the signal itself becomes very weak (as it is mostly then you can hear the noise). The ShutUp Sch-1b is different in two ways: This noise gate is not �either closed or opened�, but is sliding smoothly in between the two. Secondly, Sch-1b does not affect the actual �volume� but is continuously changing the filter parameters of an intelligent filter circuit. You may very well notice that the noise gate is half-closed when playing softly. Compared to traditional noise gates this has the impression of being perfectly responsive. The noise gate has 4 separate bands, where as the fourth has an adjustable frequency.

---

[показать]

Ph2 Phaser: Phasing works by mixing the original signal with one that is phase shifted. The phase is shifted by an LFO which frequency and depth can be controlled. This phaser has a feedback and width control for stereo effects.

---

 

Effects

---

[показать]

8Q: 8 band parametric filter with adjustable frequency, gain, Q. It comes in the types: High shelf, low shelf, high pass, low pass, band pass, notch and peak. Each band can be either a 1st order or second order IIR filter. (Please note that �first order� filters _cannot_ represent eq, band pass or notch curves.)

---

[показать]

3Q: Triple parametric filters with adjustable frequency, gain, Q. It comes in the types: High shelf, low shelf, high pass, low pass, band pass, notch and peak. (Please note that �first order� filters _cannot_ represent eq, band pass or notch curves.)

---

[показать]

Stereo Reverb R1: Stereo reverb designed to be placed last in the chain to give ambience or width to the result. Adjustable echo, pre-delay, room size. 3 filters can be programmed to shape the character of the wet part.

---

[показать]

Stereo Reverb R2: Stereo reverb designed to be placed last in the chain to give ambience or width to the result. Adjustable pre-delay, room size. 3 filters can be programmed to shape the character of the wet part. This reverb is thicker than Reverb R1; it has also different default filter parameters.

---

[показать]

Stereo widening effects: A module with combined ambience, stereo widening and exciter / enhancer. This module gives your sound a wider, fuller sound with more presence. The enhancer is working on the principle of delaying lower frequencies to allow the higher frequencies to come first, giving the sound a touch of presence and clarity. Because of the delay, the enhancer may appear to add �distance� to the sound. You can blend the enhancement with the mix control. The widening effects applies a rotating phase distortion to each channel and in combination with the ambience component you can place your audio in a rich virtual room.

---

[показать]

Channel Delay: A module which can delay each channel 0-100 ms independently. Each channel can be adjusted +-16dB. Using the ambiance option, the module acts as if the time delay represent a distance in a room. The further away from the source a channel is, the less high frequencies and less volume it has.

---

[показать]

VST host module: This module does not provide any effect or signal processing in itself, but simply allows you to load a 3rd party VST plug-in and run it as if it was a regular ReValver Mk II module. This allows you to use your favorite plug-in inside of the ReValver Mk II system. VST Plug-In Technology by Steinberg.

---

[показать]

CS3 tube compressor: A compressor is used to even out the volume so that the lower levels do not completely disappear. It would make any distortion module distort for longer. It is believed that a tube compressor sounds warmer than a a solid state variant. This is due to the slight saturation of the tubes, and the transformer adding a subtle touch of �crunch�. By rolling off some bass on the side chain, the compressor do not trigger as easily on lower frequencies, which effects the dynamics.

---

[показать]

CS2 compressor: A compressor is used to even out the volume so that the lower levels do not completely disappear. It would make any distortion module distort for longer.

---

[показать]

Gr8 Graphical Equalizer: Simple 8 band graphical equalizer with frequency bands strategically placed for bass and guitar. The bands can be adjusted manually by pressing the �T� button. Pressing �R� will reset the band.

---

[показать]

C-Verb

---

 

Utility Functions

---

[показать]

Signal splitter: The signal splitter divides the signal into 2 streams, each running in parallel using their own set of modules. In the �signal merge� module, these two streams are mixed into 1 again. It is only possible to use the signal splitter once.

---

[показать]

Frequency Analyzer: The frequency analyzer can scan the audio in real time and present the frequency content on a live display. The update speed is can be switched between 50 ms and 500 ms. The analyzer can create up to 3 snapshots and overlay them over each other. By hovering over the graph with the mouse you get an accurate readout of that position. The anti-aliased display yields a very accurate picture.

---

[показать]

Levels: A utility module to insert where ever you wish to monitor or change the volume levels. Monitors left + right channel. This module has a volume adjust and �Learn� button to automatically adjust level to 0dB.

---

[показать]

Stereo Levels Adjust: Same as �Levels� module, but with a control knob for each channel. A utility module to insert where ever you wish to monitor or change the volume levels. Monitor left + right channel. This module has a volume adjust and �Learn� button to automatically adjust level to 0dB.

---

[показать]

Tuner: Guitar tuner with two simultaneous displays, needle & strobe. With anti-aliased graphics, this tuner displays your tuning with unbelievable accuracy. The �A� is adjustable between 425Hz and 455Hz. Never go out of tune again.

---

[показать]

Simul-Tune: This is not one but 6 independent tuners running at the same time. Each channel is tuning strictly against a preset tone. That way, one can always be sure the tone has �triggered�. The tuning is presented in strobe form and represent the total tuning error for that channel. (5 of the 6 channels will probably display as wildly out of tune at any given time.) The brightness of the strobe indicate the confidence level of a frequency in that particular range. (I.e. dark display = not even close.)

---

[показать]

One Tone Stack: This module only contains one tone stack. The module has �Bass�, �Mid� and �Treble� knobs to adjust the filter aspects of any of the included tone stacks of ReValver Mk II. (The Foxy tone stack does not use the �mid� knob.)

---

[показать]

One Triode Tube: This module only contains one single triode tube with no filters, and with level adjustment before and after. Using a couple of these and you could probably build an amp yourself.

Tweak It!

Unlocking ReValver�s groundbreaking customization tools is also easy. By right-clicking on an amp model, users can �go inside� and adjust the amp�s tones and components on the Tweak Module GUI. Every tube in every amplifier can be tweaked or replaced with any one of 17 included tube types. ReValver even lets you modify power amp rectifiers, output transformers and tone stacks.

[показать]

[показать]

http://depositfiles.com/ru/files/5534027 pass: bansheebot
В архиве лекарство+небольшое FAQ по твику ламп мощников.


Патч устраняет только шипение,чтобы убрать шипение из VST-версии укажите dll-ку вручную.Для каждого отдельного модуля можно сохранять пресеты,для цепи эффектов-нет.